Peptide Dosing Calculator

📋 How to Use This Calculator ▲

🧪 Pick Your Peptide Choose from the dropdown below. It fills in common starting values for you automatically.

✏️ Check Your Numbers Make sure the vial size and water amount match what you actually have. Change anything that's different.

📊 See Your Results The calculator instantly shows how many units to draw on your syringe, plus a picture so you can see exactly where to fill.

💬 Follow the Walkthrough Below your results you'll get a plain-English, step-by-step guide that tells you exactly what to do. It updates automatically.

🛒 What You'll Need

💉

Insulin Syringes U-100 type. These are the thin ones with the tiny needle.

💧

Bacteriostatic Water Sterile water you mix your peptide with. (BAC water)

🧴

Alcohol Swabs To wipe down vial tops before each use. Keeps everything clean.

🧪

Your Peptide Vial The little glass vial with powder inside. Check the mg on the label.

🔬 How to Mix Your Peptide ▲

🧴

Step 1: Clean Everything

Grab an alcohol swab and wipe the rubber top of your peptide vial. Then wipe the top of your bacteriostatic water vial too. This keeps everything sterile.

💧

Step 2: Draw Your Water

Take a fresh syringe and pull out the amount of bacteriostatic water you need. Use the calculator below to figure out exactly how much. Most peptides use 2 mL.

💉

Step 3: Add Water to Peptide

Stick the needle through the rubber top of your peptide vial. Push the water in slowly. Aim the stream down the side of the glass, not directly onto the powder. Be gentle.

🔄

Step 4: Roll It Gently

Roll the vial slowly between your palms for about 30 to 60 seconds. Do NOT shake it. The powder should dissolve completely and look clear. If it's still cloudy, keep rolling gently.

❄️

Step 5: Store in Your Fridge

Once it's mixed, put the vial in your refrigerator. It's good for about 4 to 6 weeks after mixing. Don't freeze it. Don't leave it out on the counter.

💡 Pro tip: Always use a new, clean syringe every time you draw from your vial. Never reuse needles. And always swab the vial top with alcohol before each draw.

🧪 Choose your peptide

▼

📦 Peptide in your vial

💧 Bacteriostatic water added

📏 Your dose

💉 Your syringe size

0.3 mL

30 units

0.5 mL

50 units

1.0 mL

100 units

📊 Your Results

Concentration

2.50mg/mL

Volume to inject

0.100mL

Draw to this line

10units

Doses per vial

20doses

Draw to the 10 unit line on your syringe

💬 Here's exactly what to do

🔄 Unit Converter

Amount

→

Result

Conversion	How to calculate
mg to mcg	multiply by 1,000
mcg to mg	divide by 1,000
mL to units	multiply by 100
units to mL	divide by 100
Concentration	peptide (mg) / water (mL)
Dose volume	dose (mg) / concentration

📖 Peptide Dosage Reference

Peptide	Typical Dose	Frequency	Route
BPC-157	250 - 500 mcg	Daily	SubQ
TB-500	2.5 - 5 mg	2x/week	SubQ
Wolverine Blend	500 mcg - 1 mg	Daily	SubQ
GHK-Cu	1 - 2 mg	Daily	SubQ
CJC-1295 (no DAC)	1 - 2 mg	1-2x/week	SubQ
CJC-1295 (with DAC)	2 mg	1x/week	SubQ
Ipamorelin	200 - 300 mcg	1-3x/day	SubQ
CJC/Ipa Blend	250 - 300 mcg	Daily	SubQ
Tesamorelin	1 - 2 mg	Daily	SubQ
Tesa/Ipa Blend	1 mg	Daily	SubQ
Sermorelin	200 - 500 mcg	Nightly	SubQ
AOD-9604	300 - 600 mcg	Daily	SubQ
Retatrutide	2 - 12 mg	1x/week	SubQ
MOTS-c	5 - 10 mg	1-2x/week	SubQ
NAD+	100 - 500 mg	Daily	SubQ / IV
PT-141	1 - 2 mg	As needed	SubQ
Kisspeptin	50 - 200 mcg	Daily	SubQ
DSIP	100 - 200 mcg	Nightly	SubQ
Epithalon	5 - 10 mg	Daily (cycle)	SubQ
KPV	200 - 500 mcg	Daily	SubQ / Oral
Selank	200 - 400 mcg	Daily	Nasal
Semax	200 - 600 mcg	Daily	Nasal
LL-37	50 - 200 mcg	Daily	SubQ
ARA-290	1 - 4 mg	Daily	SubQ
Thymosin Alpha-1	1 - 3 mg	2-3x/week	SubQ
IGF-1 LR3	20 - 50 mcg	Daily	SubQ / IM
5-Amino-1MQ	50 - 100 mg	Daily	Oral

This calculator is for informational and educational purposes only. Dosages shown are general ranges gathered from published literature. Individual needs vary. Always consult a qualified healthcare professional before using any peptide. All syringe calculations assume U-100 insulin syringes (100 units = 1 mL).